Every movement with step-by-step instructions, the muscles it works, common mistakes and form tips — free, no account needed.
If you are building out back training, the Cable Bent Over Reverse Grip Row is a intermediate-level option that uses cable machine. Mechanically, the target muscles pull the arms toward and behind the torso — the reason this exercise carries over to posture, pulling strength and shoulder health. What separates this variation from other back work is that it is performed from a hip-hinged, bent-over position, using an underhand (supinated) grip, and emphasising a reversed movement direction — a detail that changes which fibres take the load and how much stability the movement demands. The 'Bent Over Reverse Grip' element in the name is the part that matters technically — it defines the exact position and path this version uses, and swapping it changes the training effect. Support comes from the biceps, rear deltoids, and core; the biceps in particular help bend the elbow and supinate the forearm, which is why fatigue there often shows up before the back is fully worked. Training this with cable machine keeps constant tension on the muscle through the entire range, though it requires an available station and correct pulley height. Programme it alongside your other back work rather than as a standalone. It assumes you already own the basic pattern and can maintain position under moderate load.
The Cable Bent Over Reverse Grip Row is primarily a back exercise, but it is never only the back doing the work.
The general rule for the Cable Bent Over Reverse Grip Row is simple: inhale on the lowering phase, exhale as you pull. For heavier sets, take a breath in at the start position, brace as though bracing for a punch, and hold that pressure through the hardest part of the rep before exhaling. Getting this right stabilises your trunk and keeps blood pressure in a sensible range.
Perform the movement slowly with a light load until the pattern feels automatic. If cable machine feels unmanageable, rehearse the same pattern with bodyweight first. Stay at this level until every Cable Bent Over Reverse Grip Row rep looks the same as the first.
Add a one- to two-second pause at the hardest position of each repetition. Alternate harder and easier Cable Bent Over Reverse Grip Row sessions rather than pushing every one.
Slow the lowering phase to three or four seconds to accumulate tension without adding weight. At this level the Cable Bent Over Reverse Grip Row is best programmed after your heaviest back work, not before it.
The Cable Bent Over Reverse Grip Row suits most healthy trainees, but it is not appropriate for everyone.
This is general educational information, not medical advice. If you are managing an injury or medical condition, check with a qualified professional before adding this exercise to your programme.
It primarily trains the back, with the biceps, rear deltoids, and core assisting. The pattern is classified as pull, so the lats, mid-back, rear delts and biceps share the workload.
It is rated intermediate. You should already be comfortable with basic back work and able to hold position under moderate load before attempting it.
A practical starting point is 4 sets of 8-12, resting 60-90 sec between sets, roughly 2x per week. Adjust from there based on how you recover.
You need cable machine. This keeps constant tension on the muscle through the entire range, though it requires an available station and correct pulley height.
As a general rule, inhale on the lowering phase, exhale as you pull. Avoid holding your breath for the entire set.
Using momentum from the lower back to swing the weight. The simplest correction is to lead with the elbow rather than the hand so the back does the work instead of the arms.
Good substitutes that train the same back pattern include Band Lying Reverse Grip Row, Barbell Meadows Row, and Upright Row Barbell. Pick whichever matches the equipment you have available.
Changing the angle changes which fibres of the back take the most tension, so it complements rather than duplicates your other back work.
The Cable Bent Over Reverse Grip Row fits into that picture as an intermediate option using cable machine, leaning on the biceps and rear deltoids alongside the back.
The back is the largest muscle group of the upper body and arguably the most important for posture, strength, and a powerful physique. It is not a single muscle but a layered system: the broad latissimus dorsi that creates width and the V-taper, the trapezius running from the neck to the mid-back, the rhomboids between the shoulder blades, the teres muscles, and the erector spinae that run along the spine and keep you upright.
Because these muscles pull in different directions, no single exercise trains the back completely. The most effective programmes combine two broad categories of movement. Vertical pulls — pull-ups, chin-ups, and lat pulldowns — emphasise the lats and build the width that makes a back look impressive from the front. Horizontal pulls — barbell rows, dumbbell rows, cable rows, and T-bar rows — build thickness through the mid-back, hitting the traps, rhomboids, and lats together. Hip-hinge movements such as the deadlift and rack pull load the entire posterior chain and develop the spinal erectors that protect the lower back.
A well-rounded back session usually includes at least one vertical pull, one horizontal pull, and some direct work for the lower back or traps. Heavy rows and pulldowns respond well to moderate rep ranges around 6 to 10, while deadlifts are typically trained in lower ranges for strength. Because the back is large and recovers well, many lifters train it twice per week with good results.
The biggest technical challenge with back training is actually feeling the back work rather than letting the biceps and forearms take over. Initiate each pull by depressing and retracting the shoulder blades — think about driving your elbows down and back rather than curling the weight with your arms. Keep the chest up, avoid jerking with momentum, and pause briefly in the fully contracted position to maximise tension. On deadlifts and rows, maintain a neutral spine; rounding under heavy load is the most common cause of injury.
Strong back muscles do more than look good. They counterbalance all the pressing and sitting that dominate modern life, pulling the shoulders back into healthy alignment and reducing the slumped posture that leads to neck and shoulder pain. Building your back also directly improves performance on nearly every other lift. Explore the popular back exercises below to assemble a complete pulling routine.