Every movement with step-by-step instructions, the muscles it works, common mistakes and form tips — free, no account needed.
Bent Over Rear Delt Fly Dumbbell is a shoulders-focused exercise built around a pull pattern and performed with dumbbell. The muscular job here is to raise and rotate the upper arm, and that translates directly into overhead capability and shoulder joint stability. What separates this variation from other shoulders work is that it is performed from a hip-hinged, bent-over position and emphasising a posterior emphasis — a detail that changes which fibres take the load and how much stability the movement demands. The 'Bent Over Rear Delt' element in the name is the part that matters technically — it defines the exact position and path this version uses, and swapping it changes the training effect. Support comes from the traps and rotator cuff; the traps in particular help elevate and retract the shoulder blades, which is why fatigue there often shows up before the shoulders is fully worked. Training this with dumbbell allows each side to work independently, exposing and correcting strength imbalances, though it demands more stabilisation, so usable load is lower than a barbell. In a training week, this fits naturally into any session where shoulders is the priority. It assumes you already own the basic pattern and can maintain position under moderate load.
The Bent Over Rear Delt Fly Dumbbell is primarily a shoulders exercise, but it is never only the shoulders doing the work.
The general rule for the Bent Over Rear Delt Fly Dumbbell is simple: inhale on the lowering phase, exhale as you pull. For heavier sets, take a breath in at the start position, brace as though bracing for a punch, and hold that pressure through the hardest part of the rep before exhaling. Consistent breathing is what keeps your brace intact from the first rep to the last.
Perform the movement slowly with a light load until the pattern feels automatic. If dumbbell feels unmanageable, rehearse the same pattern with bodyweight first. Film one set of the Bent Over Rear Delt Fly Dumbbell from the side; it's the fastest way to spot what to fix.
Add load in small increments while holding the same tempo and range you established. Hold your Bent Over Rear Delt Fly Dumbbell load for two sessions before increasing it.
Slow the lowering phase to three or four seconds to accumulate tension without adding weight. At this level the Bent Over Rear Delt Fly Dumbbell is best programmed after your heaviest shoulders work, not before it.
The Bent Over Rear Delt Fly Dumbbell suits most healthy trainees, but it is not appropriate for everyone.
This is general educational information, not medical advice. If you are managing an injury or medical condition, check with a qualified professional before adding this exercise to your programme.
It primarily trains the shoulders, with the traps and rotator cuff assisting. The pattern is classified as pull, so the lats, mid-back, rear delts and biceps share the workload.
It is rated intermediate. You should already be comfortable with basic shoulders work and able to hold position under moderate load before attempting it.
A practical starting point is 4 sets of 4-6, resting 3 min between sets, roughly 2-3x per week. Adjust from there based on how you recover.
You need dumbbell. This allows each side to work independently, exposing and correcting strength imbalances, though it demands more stabilisation, so usable load is lower than a barbell.
As a general rule, inhale on the lowering phase, exhale as you pull. Avoid holding your breath for the entire set.
Using momentum from the lower back to swing the weight. The simplest correction is to lead with the elbow rather than the hand so the back does the work instead of the arms.
Good substitutes that train the same shoulders pattern include Band Reverse Fly, Cable Leaning Lateral Raise, and Cable Lateral Raises. Pick whichever matches the equipment you have available.
Changing the angle changes which fibres of the shoulders take the most tension, so it complements rather than duplicates your other shoulders work.
Within shoulders training, the Bent Over Rear Delt Fly Dumbbell is the dumbbell variation to reach for when you want a pull pattern you can repeat consistently.
The shoulders, or deltoids, cap the upper arm and are made up of three distinct heads: the anterior (front) deltoid, the lateral (side) deltoid, and the posterior (rear) deltoid. Each head pulls the arm in a different direction, so building round, capped, three-dimensional shoulders requires training all three rather than relying on pressing alone. Well-developed shoulders create the width that makes the waist look smaller and the upper body look athletic.
Overhead pressing — with a barbell, dumbbells, or in the Arnold press variation — is the primary mass builder, heavily recruiting the front delts along with the triceps and upper chest. However, the front delts also receive a great deal of work from all chest pressing, so most lifters already have well-developed fronts and underdeveloped sides and rears. That imbalance is why lateral raises, which isolate the side delt and directly widen the shoulders, are one of the most valuable exercises in any physique routine. Rear-delt work such as face pulls and reverse flyes corrects posture and completes the rounded look.
The deltoids are made up of fibres that respond well to higher volume and frequency. Pressing can be trained in moderate ranges around 6 to 10 reps, while lateral and rear-delt isolation thrives in higher ranges of 12 to 20 with controlled tempo, since these movements are about tension and consistency rather than heavy load. Training shoulders two or three times per week, with an emphasis on the side and rear heads, produces the most balanced development.
The shoulder is the most mobile and least stable joint in the body, which makes technique and warm-up especially important. Avoid pressing behind the neck, control the weight on raises rather than swinging it up with momentum, and do not chase heavy dumbbells on lateral raises at the expense of form — leading with the elbows and stopping at shoulder height keeps tension on the delt and the strain off the joint. Including rear-delt and rotator-cuff work helps keep the shoulder healthy for years of training.
Strong, balanced shoulders improve your pressing strength, protect against common gym injuries, and dramatically improve the look of the upper body. Prioritise all three heads using the popular shoulder exercises below.