Every movement with step-by-step instructions, the muscles it works, common mistakes and form tips — free, no account needed.
Barbell Bent Over Reverse Raise (skier) is a shoulders-focused exercise built around a push pattern and performed with barbell. The muscular job here is to raise and rotate the upper arm, and that translates directly into overhead capability and shoulder joint stability. What separates this variation from other shoulders work is that it is performed from a hip-hinged, bent-over position and emphasising a reversed movement direction — a detail that changes which fibres take the load and how much stability the movement demands. Note the 'Bent Over Reverse Raise' component of the name: it specifies how this variation differs from otherwise similar shoulders movements. Support comes from the traps and rotator cuff; the traps in particular help elevate and retract the shoulder blades, which is why fatigue there often shows up before the shoulders is fully worked. Training this with barbell lets you load heavier than almost any other tool and progress in small increments, though it requires a rack or spotter once the weight gets serious. Programme it alongside your other shoulders work rather than as a standalone. It assumes you already own the basic pattern and can maintain position under moderate load.
The Barbell Bent Over Reverse Raise (skier) is primarily a shoulders exercise, but it is never only the shoulders doing the work.
The general rule for the Barbell Bent Over Reverse Raise (skier) is simple: inhale as you lower the resistance toward you, exhale as you press it away. For heavier sets, take a breath in at the start position, brace as though bracing for a punch, and hold that pressure through the hardest part of the rep before exhaling. If your breathing falls apart, it is usually the first sign the set has gone past useful.
Reduce the load and perform the Barbell Bent Over Reverse Raise (skier) for higher repetitions, focusing entirely on position rather than weight. If barbell feels unmanageable, rehearse the same pattern with bodyweight first. Stay at this level until every Barbell Bent Over Reverse Raise (skier) rep looks the same as the first.
Add a one- to two-second pause at the hardest position of each repetition. Track your Barbell Bent Over Reverse Raise (skier) numbers so you can see whether the shoulders is actually progressing.
Slow the lowering phase to three or four seconds to accumulate tension without adding weight. Use the Barbell Bent Over Reverse Raise (skier) as your accessory once your main shoulders lift is done for the day.
The Barbell Bent Over Reverse Raise (skier) suits most healthy trainees, but it is not appropriate for everyone.
This is general educational information, not medical advice. If you are managing an injury or medical condition, check with a qualified professional before adding this exercise to your programme.
It primarily trains the shoulders, with the traps and rotator cuff assisting. The pattern is classified as push, so the chest, shoulders and triceps working as a unit share the workload.
It is rated intermediate. You should already be comfortable with basic shoulders work and able to hold position under moderate load before attempting it.
A practical starting point is 4 sets of 4-6, resting 3 min between sets, roughly 2-3x per week. Adjust from there based on how you recover.
You need barbell. This lets you load heavier than almost any other tool and progress in small increments, though it requires a rack or spotter once the weight gets serious.
As a general rule, inhale as you lower the resistance toward you, exhale as you press it away. Avoid holding your breath for the entire set.
Shoulder impingement when the elbows flare excessively. The simplest correction is to keep the shoulder blades set down and back so the shoulder joint stays in a safe position.
Good substitutes that train the same shoulders pattern include Resistance Band Standing Single Arm Shoulder Flexion, Resistance Band Shoulder Adduction, and Band Seated Neutral Grip Shoulders Press. Pick whichever matches the equipment you have available.
Changing the angle changes which fibres of the shoulders take the most tension, so it complements rather than duplicates your other shoulders work.
Where the Barbell Bent Over Reverse Raise (skier) earns its place is repeatability — barbell makes the setup easy to reproduce, which is what lets you actually progress the shoulders.
The shoulders, or deltoids, cap the upper arm and are made up of three distinct heads: the anterior (front) deltoid, the lateral (side) deltoid, and the posterior (rear) deltoid. Each head pulls the arm in a different direction, so building round, capped, three-dimensional shoulders requires training all three rather than relying on pressing alone. Well-developed shoulders create the width that makes the waist look smaller and the upper body look athletic.
Overhead pressing — with a barbell, dumbbells, or in the Arnold press variation — is the primary mass builder, heavily recruiting the front delts along with the triceps and upper chest. However, the front delts also receive a great deal of work from all chest pressing, so most lifters already have well-developed fronts and underdeveloped sides and rears. That imbalance is why lateral raises, which isolate the side delt and directly widen the shoulders, are one of the most valuable exercises in any physique routine. Rear-delt work such as face pulls and reverse flyes corrects posture and completes the rounded look.
The deltoids are made up of fibres that respond well to higher volume and frequency. Pressing can be trained in moderate ranges around 6 to 10 reps, while lateral and rear-delt isolation thrives in higher ranges of 12 to 20 with controlled tempo, since these movements are about tension and consistency rather than heavy load. Training shoulders two or three times per week, with an emphasis on the side and rear heads, produces the most balanced development.
The shoulder is the most mobile and least stable joint in the body, which makes technique and warm-up especially important. Avoid pressing behind the neck, control the weight on raises rather than swinging it up with momentum, and do not chase heavy dumbbells on lateral raises at the expense of form — leading with the elbows and stopping at shoulder height keeps tension on the delt and the strain off the joint. Including rear-delt and rotator-cuff work helps keep the shoulder healthy for years of training.
Strong, balanced shoulders improve your pressing strength, protect against common gym injuries, and dramatically improve the look of the upper body. Prioritise all three heads using the popular shoulder exercises below.